Shock Thermal Air Test Chamber: The equipment is divided into three sections: the high temperature chamber, the low temperature chamber and the testing chamber.The TFT LCD touch panel controller was made in Japan, can display Chinese / English. Big size TFT LCD panels are also adopted.High formula memory capacity can be set to 120 patterns. The maximum […]
3 Chambers High Low Temperature Shock Chamber ZME-2012B Equipment Summary: 3 Chambers High Low Temperature Shock Chamber is divided into high temperature area, low temperature area and test area three parts, each area is a unique insulation structure, so doing hot and cold impact test. High-temperature impact test orlow-temperature impact test, the maximum time is up […]
Humidity Thermal Shock Chambers HZ-2004A Product Description Equipment summary: Humidity Thermal Shock Chambers is applied to test the materials in heat-resistance, cold-resistance, dry-resistance, moisture-resistance. It is simple to operate and program easy to edit. It can show the setvalues and operative time. Corresponding standard: 1.International Electrotechnical Commission Standard: IEC68-2-03_test method Ca_Steady damp-heat IEC68-2-01_test method A_cold […]
Temperature test chambers/backing oven/industrial oven/thermal shock test chambers/uv accelrated weathering test chamber Application: Simulated sunlight damage on the material and product test, widely used in the evaluation of material climate resistant. Temperature test chambers/backing oven/industrial oven/thermal shock test chambers/uv accelrated weathering test chamber Technical parameters: Model UV-230 Internal Dimension WxHxD (cm) 115x50x40 External Dimension WxHxD (cm) 150x150x55 Applicable Standard GB/T16422,GB/T5170.9 Temperature Range R.T.+10°C~+70°C Temperature Fluctuation ±0.5°C Humidity Range ≥95%R.H. Environmental Temperature for Use +5°C~+35°C Test Light Source UVA,UVB UV light Wave Length of Test light Source (nm) 280~400 Center Distance between Sample and Tube (mm) 50±2 Center Distance Between Tubes (mm) 75±2 Material of Internal Case Stainless steel with sanding polish Material of External Case […]
Thermal shock chambers new york Product Description A. Equipment summary: Double zones thermal shock test chambers used to test the change of material under extremely high temperature and extremely low temperature environment that continue alternation in the shortest time, Testing the chemical changes or physical damage of material caused by the thermal expansion and contraction. Testing box divided two parts, one is high-temperature region, another is low-temperature region, the testing sample placed on the moving basket, using unique heat storage and cool storage, the cylinder taking basket moves up and down in the hot and cold region to complete the hot and cold temperature impact testing; applied to test the material, including metal, plastic, rubber, electronics and other materials,it can be used as a basis for improvement of their products. B. Technical parameters: 1.Model Double zones thermal shock test chambers 2.Temperature range A.high-temperature:+60℃~+150℃ B.low-temperature:-10℃~-40℃ 3.Control temperature ±2℃ 4.resolution 0.01℃ 5.Heating time at high-temperature region RT~+150℃ about 35min(RT is from +5~+30℃) 6.Cooling time at low-temperature region RT~-40℃ about 50min(RT is from +5~+30℃) 7.Moving time and temperature recover time A. testing basket moving from high-temperature to low-temperature spend 10sec B.after exchanging the temperature,the temperature recovery time: 3min~5min (Stabilization time ≥ 30min) 8.Device noise Below 75dB 9.Weight 10Kg 10.Testing region(hot and cold) 50cm(W)*50cm(H)*50cm(D) 11.Outside size 140cm(W)*180cm(H)*142cm(D) 12.Testing basket size […]
Product Description New air-to-air thermal gas shock testing machine chambers Brief introduction and application fields: The Thermal Shock tester is applied to test electronic chip IC, PCB, of semiconductor ceramic and polymer materials physical changes, and test the bearing extent of the material structures and composite material in an instant and continuous high temperature and […]
product detailed introduction 1.Brand:eternal 2.Material:plastic and steel 3.Technique:Heat preservation nails is made by largely automatic injection-molding machine to produce 4.Feature:the sudden change in temperature resistance, anti-corrosion, heat-hardy; High-capacity,high pressure, good tensile properties; After loading is noteasy deformation cast reduce vibration, noise absorption and sound insulation characteristics. Installation is simple and can Hammering do not need […]
Thermal Shock Chamber Industry 2016 Global and China Market Research Report The ‘Global and Chinese Thermal Shock Chamber Industry, 2011-2021 Market Research Report’ is a professional and in-depth study on the current state of the global Thermal Shock Chamber industry with a focus on the Chinese market. The report provides key statistics on the market […]
Chamber Management Tools Web Manager Remote monitoring and operation The Web Manager leapfrogs competitive remote access solutions by hosting the software remotely, at the chamber. Real-time remote monitoring and programming (resetting/start & stop control) make the environmental test easier and comfortable. No local software to install, just a web browser and access to the LAN […]
Thermal Shock Environmental Chambers is divided into three sections: the high temperature chamber, the low temperature chamber and the testing chamber. The color touch panel control system was made in Japan can display Chinese / English. The big size liquid-crystal LCD has been adopted. High formula memory capacity may be set to 120 patterns. The maximum cycle setting […]
